Bed and column
• Pearlite grey cast iron quality EN-GJL-300 structures
• Thermally stabilized and robustly reinforced table- bed with ribs at the bottom every 500 mm. Hardness of 190-220 HB
• Load capacity of 6.000 Kg / m2
• Table width 1.100 mm. 7 “T” slots
• Travelling column with 3 guide ways
• 2 linear guide ways size 55 at the front
• Rear box type guide way at the rear

Bed-column slide
• Pearlite grey cast iron quality frame EN-GJL-300
• Thermally stabilized and robustly reinforced internally with ribs. Hardness of 190-220 HB
• 2 linear guide ways size 55
• 6 linear carriages size 55

Rear slide
• Made of ST-50 steel, stabilized and reinforced
• Box type guide way with section size 140 x 50 mm, Surface hardness of 60 HRC with 6 conical carriages

Column and ram slides
• Made by pearlite high quality grey cast iron (EN-GJL-300)
• Thermally stabilized and robustly internally reinforced frames with ribs
• Static and dinamilcally well balanced structure
• Hardness of 190-220 HB
• Guiding by 2 linear guide ways size 45 (Z & Y slides)
• 8 linear carriages (4+4) on Z slide
• 6 linear carriages (3+3) on Y slide

Ram and head
• The ram is made of pearlitic grey cast iron, quality EN-GJL-300 (UNE-EN 1561 standard), with a hardness of 190-220 HB, and is dimensioned and robustly reinforced with inner ribs to absorb the cutting and weight forces, and studied by finite elements.
• The ram has two size-45 rolling linear guide ways with recirculation rolls carriages, closed and protected against contamination.
• Mechanical compensation to get perpendicularly of main axis with the table
• Main motor with 2 speed reduction gearbox
• Automatic universal milling head 2,5 ° x 2,5 °

• Both bodies of spindle head are made of spheroidal graphite cast iron, quality EN-GJS-HB155 (UNE-EN 1563 standard), with a hardness of 130-180 HB.
• The Spindle head is made up of two parts joined at 45º, which rotates around each other and are joined to the front part of the ram.
o Hardened and ground Klingerlberg-type epicyclical taper gears.
o Hardened and ground spindle shaft DIN 5480 (gear type).
o Main spindle bearing diameter 85 x 130 mm.
o Super-precision angular-contact ball bearings on the entire head.
• Hydro-mechanic type tool clamping system (clamping force 12 / 14 kN).

Drivings and others
• Frontal/ lateral guarding tight to the machine with two doors with machine traverse opening possibility.
• The rear part of the machine is protected with a fence, which has fitted a door with protected access and safety system.
• Operator cabinet moves with the column, protected with safety system.
• All the doors are equipped with windows to visualize the work area. Those windows are for safety requests of the machine and they are designed to resist an impact according with machine features.
• The Z-axis (vertical slide and ram) is balanced by means of a counterweight system, made up of a hydraulic cylinder and its rod attached to the vertical slide, and connected to a nitrogen accumulator, which together form a closed circuit, so that there is no need for an additional hydraulic unit during operation.
• If for any reason, a discharge of the circuit takes place and the pressure drops below the established limits for a correct operation of the system, a device manually charges the system again. The instructions to charge manually are detailed in machine maintenance manual.

• Doble rack-pinion stransmission system
• 2 independent motors with high accuracy planetary reductors
• “Master – Slave” driving
• Motor’s powers 2 x 5,37 Kw-36 Nm
• Pushing force 31.140,43 N
• Ball screw transmission system
 Size Ø 50 x 16 mm for Y axis
 Size Ø 50 x 12 mm for Z axis
• AC Brushless servomotors
• Power for motors Z & Y: 5,37 Kw – 36 Nm
• Pushing force for Z axis: 18.535,44 N
• Pushing force for Y axis: 13.901,58 N